Search found 14 matches

by Jim585
Sat May 09, 2020 6:07 pm
Forum: RR / Post - 1898
Topic: 141 in 35 rem. loads
Replies: 6
Views: 1673

Re: 141 in 35 rem. loads

Example: trying to load 35 grains using my Lee Perfect Powder Measure, sometimes I am short 1 to 2 grains! Tapping the unit sharply will sometimes release some of the "stuck" extruded powder, but I don't always get my full 35 grains. Perhaps I should consider flake or granular powder if I want to us...
by Jim585
Sat May 09, 2020 6:14 am
Forum: RR / Post - 1898
Topic: 141 in 35 rem. loads
Replies: 6
Views: 1673

Re: 141 in 35 rem. loads

I am trying to reload 35 Remington with a Lee Perfect Powder Measure, but it does not seem to dispense powder very consistently with extruded powders IMR3031 & IMR4064.
What powder measures do you all use for extruded powders?
by Jim585
Sun Mar 29, 2020 6:16 am
Forum: RR / Post - 1898
Topic: Remington model 14 fail to fire
Replies: 4
Views: 311

Re: Remington model 14 fail to fire

My 141 always fires when loading the cartridge into the magazine and cycling into the chamber.
I experienced failures to fire only when loading a cartridge directly into the chamber. Perhaps I was not completely cocking the hammer?
by Jim585
Wed Mar 18, 2020 5:50 am
Forum: RR / Post - 1898
Topic: Model 14 / 141 After Market Ammo / BULLETIN #14
Replies: 2
Views: 430

Re: Model 14 / 141 After Market Ammo / BULLETIN #14

Thanks Jim, you have generously shared your wisdom here over the years. Wish all your "BULLETINS" could be pulled together under one tab in this forum. -Jim
by Jim585
Tue Feb 25, 2020 6:13 pm
Forum: RR / Post - 1898
Topic: Hard case for Remington 14 & 141 ?
Replies: 4
Views: 371

Re: Hard case for Remington 14 & 141 ?

I have used soft cases. Found this post, as there are times I would like to have additional protection for my rifles while traveling.
https://www.24hourcampfire.com/ubbthrea ... st14590054
by Jim585
Sun Feb 02, 2020 4:17 pm
Forum: RR / Post - 1898
Topic: Hard case for Remington 14 & 141 ?
Replies: 4
Views: 371

Re: Hard case for Remington 14 & 141 ?

If no one here uses a hard case, then what is your favorite carrying case to best protect your models 14 & 141 ?
by Jim585
Sat Feb 01, 2020 3:43 pm
Forum: RR / Post - 1898
Topic: Hard case for Remington 14 & 141 ?
Replies: 4
Views: 371

Hard case for Remington 14 & 141 ?

I want a good hard case to protect my Remington 141 & am looking at this:
https://www.jeffsoutfitters.com/product ... tion-case/
Any other recommendations?
by Jim585
Tue Jan 21, 2020 6:18 pm
Forum: RR / Post - 1898
Topic: Snap caps for 35 Remington?
Replies: 5
Views: 485

Re: Snap caps for 35 Remington?

Thank you both for your helpful comments. Much appreciated. -Jim
by Jim585
Sat Jan 18, 2020 11:35 am
Forum: RR / Post - 1898
Topic: Snap caps for 35 Remington?
Replies: 5
Views: 485

Snap caps for 35 Remington?

Unable to find Snap Caps for 35 Remington, I stumbled upon this Gunbroker post: https://www.gunbroker.com/item/853250122 Seems like I could make a few of these, but wondering: 1- what rubber would fit snugly in the primer pocket & how long would this rubber last? 2- should a bit of sand be loaded to...
by Jim585
Thu Nov 21, 2019 4:36 pm
Forum: RR / Post - 1898
Topic: Ken Blauch has died!
Replies: 5
Views: 946

Re: Ken Blauch has died!

I am sorry to hear this news of Ken Blauch.
I acquired his book last year at Cornell Publications:
https://www.cornellpubs.com/old-guns/it ... em_id=5626
by Jim585
Fri Mar 01, 2019 3:32 pm
Forum: RR / Post - 1898
Topic: Non lead bullets for 35 Rem 141 ?
Replies: 2
Views: 718

Re: Non lead bullets for 35 Rem 141 ?

Thanks Jim, that is what I thought you would say. Always good advice. Just wondering about the future if they mandate non lead ammo? Perhaps then it will be best to use a different firearm. Until then, I will enjoy my 141. -Jim
by Jim585
Wed Feb 27, 2019 7:10 pm
Forum: RR / Post - 1898
Topic: Non lead bullets for 35 Rem 141 ?
Replies: 2
Views: 718

Non lead bullets for 35 Rem 141 ?

Is anyone hunting with Non lead bullets in their 35 Rem 141 ?
Any bullet suggestions for reloading?
Thank you, Jim
by Jim585
Sat Jul 21, 2018 8:04 pm
Forum: RR / Post - 1898
Topic: Model 14 - Dissassembly
Replies: 30
Views: 24483

Re: Model 14 - Dissassembly

I am looking for contact info for NambuJim, as I would like to send him my 141 for repair.
Thank you, Jim585
by Jim585
Sat Jul 21, 2018 6:11 pm
Forum: RR / Post - 1898
Topic: Model 14/14-1/2 & 141 Repairs & Tips
Replies: 7
Views: 2614

Re: Model 14/14-1/2 & 141 Repairs & Tips

How do I contact NambuJim to send in my 141 for repair? Thank you, Jim585