Search found 80 matches
- Fri Dec 22, 2023 12:10 pm
- Forum: RR / Post - 1898
- Topic: Remington 552 chambering problem
- Replies: 2
- Views: 264
Re: Remington 552 chambering problem
The failure to cycle was caused by the trigger not resetting. I installed a 3lb spring and everything resumed operating properly. This is not the rule, but an exception to the 2lb spring being perfect for ALL 552's. Trigger mechanisms are made in different years and although perhaps made from the sa...
- Fri Dec 22, 2023 11:48 am
- Forum: RR / Post - 1898
- Topic: Remington 552 chambering problem
- Replies: 2
- Views: 264
Re: Remington 552 chambering problem
Took the trigger group out and inspected it. Found nothing obvious. Reassembled and fire tested it. Now it loads ok, but the trigger isn't resetting. It's a single shot ! Obviously there is something interfering with the trigger mechanism... which is very clean. All the levers move freely and there ...
- Fri Dec 22, 2023 10:37 am
- Forum: RR / Post - 1898
- Topic: Remington 552 chambering problem
- Replies: 2
- Views: 264
Remington 552 chambering problem
Bought a 552, and it was Filthy but functioned well. I had a tough time getting the barrel out. Took it to Miller's Gun in Jacksonville NC to have him remove it without damaging anything. Then brought it home to clean. Four hours later I had it looking pretty again. Reassembled using a Youtube Video...
- Tue Nov 07, 2023 10:48 am
- Forum: RS / Post - 1898
- Topic: SKEET vs SKEET-B vs SKEET-T
- Replies: 1
- Views: 539
SKEET vs SKEET-B vs SKEET-T
See variations on the 1100 SKEET shotguns. Just recently purchased a 410 SKEET-T, with beautiful figure and high gloss finish & laser cut checkering.
Anyone have the info, or a link to where it can be found.
Anyone have the info, or a link to where it can be found.
- Wed Sep 13, 2023 12:39 pm
- Forum: WTB / Other
- Topic: New board on-line
- Replies: 1
- Views: 2202
New board on-line
I've started http://obxguntrader.com It's FREE and I encourage you to help populate it. If you find categories missing, just let me know and they'll be added.
It's very much like this board... likely the same software.
It's very much like this board... likely the same software.
- Sat Jul 29, 2023 5:00 pm
- Forum: RS / Post - 1898
- Topic: Forend Support 1100 LT-20
- Replies: 2
- Views: 612
Re: Forend Support 1100 LT-20
Thanks for the correction. There were markings on it that lead me to believe it was 1967. I was/am looking for a 24" Rem-choke VR barrel for it. Am selling the 21" "Special Field" Rem-choke VR barrel asking $550 due to rarity. I did get a 28" barrell but don't know if my wif...
- Tue Jul 04, 2023 3:06 pm
- Forum: RS / Post - 1898
- Topic: Forend Support 1100 LT-20
- Replies: 2
- Views: 612
Forend Support 1100 LT-20
I recently purchased a 1967 vintage 1100 LT-20. It's forend is a bit too loose for my taste... I've noticed there are no forend supports manufactured for any of the sub-gauge shotguns. Why? I have MANY Remington 1100's and most are tight enough. So I am assuming that the problem isn't common. I atte...
- Sat Jul 01, 2023 1:18 pm
- Forum: RS / Post - 1898
- Topic: Model 11 questions
- Replies: 2
- Views: 700
Re: Model 11 questions
The choke marking is on the left rear of the barrel near the receiver. I recommend against modification other than preservation. The guns are great, and built well. So unless you're missing a lot of screws or have splits in the stock, it's likely safe to shoot, and use. There seems to be a greater i...
- Fri May 26, 2023 1:13 pm
- Forum: RP / Post - 1898
- Topic: Remington F300126 GasPiston
- Replies: 0
- Views: 875
Remington F300126 GasPiston
I bought some Gas Piston Seals and was backorderd on the piston. I've never had one fail, but since I have many 12ga 1100's think it's a good idea to have a few. The part I have is the New Style Piston_Seal.png and I need the Gas_Piston.png If you have spare parts, or will trade a couple pistons for...
- Mon Mar 13, 2023 6:38 pm
- Forum: RS / Post - 1898
- Topic: 20ga Barrel Seal Activator (not an O ring)
- Replies: 1
- Views: 556
20ga Barrel Seal Activator (not an O ring)
I have been plauged by poor cycling with light loads. Seeing a barrel seal activator made me think this may be to help the low power target loads cycle. Bought one... Not much written about them I am unsure if it is strictly an 1187 thing or if it can be used safely in an 1100. I can take the barrel...
- Thu Feb 23, 2023 10:18 am
- Forum: RS / Post - 1898
- Topic: Shotgun Butt Stock contours 870, 1100, 1187 etc
- Replies: 2
- Views: 637
Re: Shotgun Butt Stock contours 870, 1100, 1187 etc
I pulled a couple stock photos and overlaid them. Clearly the old darker stock is taller... overlaid buttstock.jpg old_buttstock.png new_buttstock.png Difficult to get precise with overlay, but this shows the difference in height of pad. As well the older ones are narrower. Perhaps there is someone ...
- Tue Feb 21, 2023 6:20 pm
- Forum: RS / Post - 1898
- Topic: Rem Arms 870 Fieldmaster stock contour
- Replies: 2
- Views: 582
Re: Rem Arms 870 Fieldmaster stock contour
I have a few late model 1100's that now have Remington Supercell pads and they fit very nicely.
- Mon Feb 20, 2023 10:15 pm
- Forum: RS / Post - 1898
- Topic: Shotgun Butt Stock contours 870, 1100, 1187 etc
- Replies: 2
- Views: 637
Shotgun Butt Stock contours 870, 1100, 1187 etc
I have supercell recoil pads and need to know when the stock contour changed. I believe somewhere around 1980. Can anyone confirm this. I know some of the early models had thinner taller butstock wood...
Virginian... are you out there ?
Regards
Dave
Virginian... are you out there ?
Regards
Dave
- Tue Feb 07, 2023 2:18 pm
- Forum: RS / Post - 1898
- Topic: 1187 Super Mag Bolt
- Replies: 2
- Views: 562
1187 Super Mag Bolt
Curious if there is any difference (dimensional or strength) of a Super Mag bolt assembly.
Seems to me it's the same as any 1187 12ga bolt eh?
Please tell me if you know the correct answer... no guessing please. I do my own guessing...
Dave
Seems to me it's the same as any 1187 12ga bolt eh?
Please tell me if you know the correct answer... no guessing please. I do my own guessing...
Dave
- Mon Feb 06, 2023 10:02 pm
- Forum: RS / Post - 1898
- Topic: The Remington 11-87 Discontinued?
- Replies: 3
- Views: 2739
Re: The Remington 11-87 Discontinued?
A month ago I could buy receivers, but they're all gone now... get a used one... try for an 1100G3 you'll not regret it. I would recommend buying a used 1187 and fix up whatever is not new enough looking to suit you. I have a fondness for the 1100G3's which are a Deluxe 1187 for all practical purpos...