Search found 685 matches

by Virginian
Wed Jul 05, 2023 9:26 am
Forum: RS / Post - 1898
Topic: Forend Support 1100 LT-20
Replies: 2
Views: 604

Re: Forend Support 1100 LT-20

You do not have a 1967 LT-20. They didn't come out until 1977. There is no rear fore end support on an LT/LW 20 ga. 1100. The fit of the fore end on the magazine tube and two reliefs cut to fit the receiver on the rear are supposed to do it. Taking some masking tape to the inside of the hole in the ...
by Virginian
Sat Apr 29, 2023 7:22 pm
Forum: RS / Post - 1898
Topic: Late late late Model 11?
Replies: 6
Views: 1173

Re: Late late late Model 11?

Researcher will be along and answer any questions you may have.
by Virginian
Thu Mar 30, 2023 4:38 am
Forum: RS / Post - 1898
Topic: Model 11 with brass pins on receiver, Polychoke
Replies: 3
Views: 1335

Re: Model 11 with brass pins on receiver, Polychoke

I have only seen that once before. It was on a WWII era Model 11 that Navy Special Services had as a loaner back in the '60s. The gun had been used to teach aerial gunnery, had an odd attachment that had been on the fore end to mount it I guess, and had Lyman screw on choke tubes. The pins didn't se...
by Virginian
Wed Mar 15, 2023 4:57 am
Forum: RS / Post - 1898
Topic: 20ga Barrel Seal Activator (not an O ring)
Replies: 1
Views: 546

Re: 20ga Barrel Seal Activator (not an O ring)

If the action will close normally with the activator installed, it wont hurt anything because it is not blocking gas flow to the relief ports, because there aren't any. Unlikely to solve your issue. Rather than drilling the ports, first I would try "wallowing" out the ports, one at a time,...
by Virginian
Tue Feb 21, 2023 7:20 am
Forum: RS / Post - 1898
Topic: Shotgun Butt Stock contours 870, 1100, 1187 etc
Replies: 2
Views: 627

Re: Shotgun Butt Stock contours 870, 1100, 1187 etc

Remington changed the checkering style but not the basic stock contours in 1979. Then in 1987 with the 11-87, they started introducing a different stock finish. Throughout the 90s they started making changes to various models. They tried to kill off the 1100, unsuccessfully. They started with differ...
by Virginian
Sat Feb 18, 2023 2:11 pm
Forum: RS / Post - 1898
Topic: Remington 11-87 Bolt not locking rearward
Replies: 3
Views: 661

Re: Remington 11-87 Bolt not locking rearward

#1 suspect, a bent carrier latch. Possibly caused by someone dropping the hammer on the trigger group out of the gun. Gun should still function okay otherwise. Good luck if you try bending it back.
by Virginian
Tue Feb 07, 2023 6:05 pm
Forum: RS / Post - 1898
Topic: Rem Arms 870 Fieldmaster stock contour
Replies: 2
Views: 569

Re: Rem Arms 870 Fieldmaster stock contour

I have never seen a pre-shaped pad perfectly fit a Remington wood stock, on any model.
by Virginian
Tue Feb 07, 2023 2:19 pm
Forum: RS / Post - 1898
Topic: 1187 Super Mag Bolt
Replies: 2
Views: 556

Re: 1187 Super Mag Bolt

I thought they were unique. I don't remember the difference now.
by Virginian
Tue Jan 31, 2023 11:49 am
Forum: RS / Post - 1898
Topic: Remington 31 20ga short barrel question
Replies: 2
Views: 764

Re: Remington 31 20ga short barrel question

Barrel has been cut. Not a factory bead. Check the choke.
by Virginian
Sat Jan 21, 2023 3:08 pm
Forum: RS / Post - 1898
Topic: Ken Rucker’s Bump-Buster Stock and Forearm
Replies: 3
Views: 683

Re: Ken Rucker’s Bump-Buster Stock and Forearm

If not using it, I would remove it. Liable to bind on the action bars.
by Virginian
Sat Jan 21, 2023 9:44 am
Forum: RS / Post - 1898
Topic: Ken Rucker’s Bump-Buster Stock and Forearm
Replies: 3
Views: 683

Re: Ken Rucker’s Bump-Buster Stock and Forearm

As long as the fore end fits snug, you can get by without the fore end support. The LW/LT 20s do not employ a fore end support.
by Virginian
Sun Jan 08, 2023 2:39 pm
Forum: RS / Post - 1898
Topic: Gifted a model 11
Replies: 5
Views: 939

Re: Gifted a model 11

Researcher will be along to answer your questions. The buttstock and pad are not original, and the magazine extension is removable.
by Virginian
Sat Nov 05, 2022 5:56 pm
Forum: RS / Post - 1898
Topic: Remington 1100 & 11-87 Replacement Barrels
Replies: 3
Views: 861

Re: Remington 1100 & 11-87 Replacement Barrels

I don't know what they are doing. They have been slow to "ramp up" production on anything but the Fieldmaster.
by Virginian
Sat Nov 05, 2022 5:50 am
Forum: RS / Post - 1898
Topic: Remington 1100 & 11-87 Replacement Barrels
Replies: 3
Views: 861

Re: Remington 1100 & 11-87 Replacement Barrels

I do not believe RemArms is making spare bbls yet. Check ebay, GunBroker, etc. They are out there at elevated prices.
by Virginian
Thu Oct 13, 2022 10:41 pm
Forum: RS / Post - 1898
Topic: 1100 - which model is this?
Replies: 5
Views: 938

Re: 1100 - which model is this?

It is a standard second generation Model 1100. If it was a SKEET model, it should say so. Serial # and barrel(s) info would be helpful. Looks to be in good shape. $600 to $750.